IBM Enterprise Systems Architecture

IBM Enterprise Systems Architecture is an instruction set architecture introduced by IBM as Enterprise Systems Architecture/370 (ESA/370) in 1988. It is based on the IBM System/370-XA architecture.

It extended the dual-address-space mechanism introduced in later IBM System/370 models by adding a new mode in which general-purpose registers 1–15 are each associated with an access register referring to an address space, with instruction operands whose address is computed with a given general-purpose register as a base register will be in the address space referred to by the corresponding address register.

The later Enterprise Systems Architecture/390 (ESA/390), introduced in 1990, added a facility to allow device descriptions to be read using channel commands and, in later models, added instructions to perform IEEE 754 floating-point operations and increased the number of floating-point registers from 4 to 16.

Enterprise Systems Architecture is essentially a 32-bit architecture; as with System/360, System/370, and 370-XA, the general-purpose registers are 32 bits long, and the arithmetic instructions support 32-bit arithmetic. Only byte-addressable real memory (Central Storage) and Virtual Storage addressing is limited to 31 bits, as is the case with 370-XA. (IBM reserved the most significant bit to easily support applications expecting 24-bit addressing, as well as to sidestep a problem with extending two instructions to handle 32-bit unsigned addresses.) It maintains problem state backward compatibility dating back to 1964 with the 24-bit-address/32-bit-data (System/360 and System/370) and subsequent 24/31-bit-address/32-bit-data architecture (System/370-XA). However, the I/O subsystem is based on System/370 Extended Architecture (S/370-XA), not on the original S/370 I/O instructions.

On February 15, 1988, IBM announced Enterprise Systems Architecture/370 (ESA/370) for 3090 enhanced ("E") models and for 4381 model groups 91E and 92E.

In addition to the primary-space and secondary-space addressing modes that later System/370 models, and System/370 Extended Architecture (S/370-XA) models, support, ESA has an access register mode in which each use of general register 1–15 as a base register uses an associated access register to select an address space. In addition to the normal address spaces that machines with the dual-address-space facility support, ESA also allows data spaces, which contain no executable code.

A machine may be divided into Logical Partitions (LPARs), each with its own virtual system memory so that multiple operating systems may run concurrently on one machine.

An important capability to form a Parallel Sysplex was added to the architecture in 1994.

ESA/390 also extends the Sense ID command to provide additional information about a device, and additional device-dependent channel commands, the command codes for which are provided in the Sense ID information, to allow device description information to be fetched from a device.

Starting with the System/390 G5, IBM introduced:

• the basic floating-point extensions facility, which increases the number of floating-point registers from 4 (0, 2, 4, 6) to 16 (0–15);
• the binary floating-point (BFP) extensions facility, which supports IEEE 754 binary floating-point numbers, with an additional floating-point control (FPC) register to support IEEE 754 modes and errors;
• the floating-point support (FPS) extensions facility, which adds instructions to load and store floating-point numbers regardless of whether they're in hexadecimal or IEEE 754 format and to convert between those formats;
• the hexadecimal floating-point (HFP) extensions facility, which adds new hexadecimal floating-point instructions corresponding to some binary floating-point instructions.

Some PC-based IBM-compatible mainframes which provide ESA/390 processors in smaller machines have been released over time, but are only intended for software development.

ESA/390 adds the following facilities

All models

• Access-list-controlled protection

Some models

• Concurrent sense
• PER 2
• Storage-protection override
• Move-page facility 2
• Square root
• String instruction
• Suppression on protection with virtual-address enhancement
• Set address space control fast
• Subspace group
• Called-space identification
• Checksum
• Compare and move extended
• Immediate and relative instruction
• Branch and set authority
• Perform locked operation
• Additional floating-point
• Program call fast
• Resume program
• Trap
• Extended TOD clock
• TOD-clock-control override
• Store system information
• Extended translation 1
• Extended translation 2
• z/Architecture (certain instructions)
• Enhanced input/output

The following channel commands are new, or have their functionality changed, in ESA/390:

S370-ESA

IBM Enterprise Systems Architecture/370 Principles of Operation (PDF) (First ed.). IBM. August 1988. SA22-7200-0.

S/390-ESA

IBM Enterprise Systems Architecture/390 Principles of Operation (PDF) (Ninth ed.). IBM. June 2003. SA22-7201-08.