The ASME Boiler and Pressure Vessel Code (BPVC) is a set of standards published by the American Society of Mechanical Engineers (ASME) that provides rules for the design, fabrication, inspection, testing, and certification of boilers and pressure vessels.
The BPVC is developed and updated through a consensus process managed by ASME committees, with participation from volunteer technical experts representing industry, regulators, and other stakeholders.
ASME also operates a conformity assessment and certification system under which accredited organizations—including manufacturers and authorized inspection agencies—may apply ASME Code Symbol Stamps to equipment that meets BPVC requirements.
The BPVC was created in response to public outcry after several serious explosions in the state of Massachusetts. A fire-tube boiler exploded at the Grover Shoe Factory in Brockton, Massachusetts, on March 20, 1905, which resulted in the deaths of 58 people and injured 150. Then on December 6, 1906, a boiler in the factory of the P.J. Harney Shoe Company exploded in Lynn, Massachusetts. As a result, the state of Massachusetts enacted the first legal code based on ASME's rules for the construction of steam boilers in 1907.
ASME convened the Board of Boiler Rules before it became the ASME Boiler Code Committee which was formed in 1911. This committee put in the form work for the first edition of the ASME Boiler Code - Rules for the Construction of Stationary Boilers and for the Allowable Working Pressures, which was issued in 1914 and published in 1915.
The first edition of the Boiler and Pressure Vessel Code, known as the 1914 edition, was a single 114-page volume. It developed over time into the ASME Boiler and Pressure Vessel code, which today has over 92,000 copies in use, in over 100 countries around the world. As of March 2011[update] the document consisted of 16,000 pages in 28 volumes.
After the first edition of the Code, the verifications required by the Code were performed by independent inspectors, which resulted in a wide range of interpretations. Hence in February 1919, the National Board of Boiler and Pressure Vessel Inspectors was formed.
This section needs to be updated. The reason given is: Table is extremely vague and only includes a subset of all changes to the code in each issue year. It would be better to either provide reference links to official documentation describing all changes between code versions, or perhaps to only show changes to the most recent code version.. (April 2022) |
LIST OF SECTIONS
The following is the structure of the 2021 Edition of the BPV Code:
ADDENDA
Addenda, which include additions and revisions to the individual Sections of the Code, are issued accordingly for a particular edition of the code up until the next edition. Addenda is no longer in use since Code Edition 2013. It has been replaced by two years edition period.
INTERPRETATIONS
ASME's interpretations to submitted technical queries relevant to a particular Section of the Code are issued accordingly. Interpretations are also available through the internet.
CODES CASES
Code Cases provide rules that permit the use of materials and alternative methods of construction that are not covered by existing BPVC rules. For those Cases that have been adopted will appear in the appropriate Code Cases book: "Boilers and Pressure Vessels" and "Nuclear Components."
Codes Cases are usually intended to be incorporated in the Code in a later edition. When it is used, the Code Case specifies mandatory requirements which must be met as it would be with the Code. There are some jurisdictions that do not automatically accept Code Cases.
It has been suggested that this section be split out into another article titled ASME BPVC Section II - Materials. (Discuss) (March 2023) |
The section of the ASME BPVC consists of 4 parts.
Part A - Ferrous Material Specifications
This Part is a supplementary book referenced by other sections of the Code. It provides material specifications for ferrous materials which are suitable for use in the construction of pressure vessels.
The specifications contained in this Part specify the mechanical properties, heat treatment, heat and product chemical composition and analysis, test specimens, and methodologies of testing. The designation of the specifications start with 'SA' and a number which is taken from the ASTM 'A' specifications.
Part B - Nonferrous Material Specifications
This Part is a supplementary book referenced by other sections of the Code. It provides material specifications for nonferrous materials which are suitable for use in the construction of pressure vessels.
The specifications contained in this Part specify the mechanical properties, heat treatment, heat and product chemical composition and analysis, test specimens, and methodologies of testing. The designation of the specifications start with 'SB' and a number which is taken from the ASTM 'B' specifications.
Part C - Specifications for Welding Rods, Electrodes, and Filler Metals
This Part is a supplementary book referenced by other sections of the Code. It provides mechanical properties, heat treatment, heat and product chemical composition and analysis, test specimens, and methodologies of testing for welding rods, filler metals and electrodes used in the construction of pressure vessels.
The specifications contained in this Part are designated with 'SFA' and a number which is taken from the American Welding Society (AWS) specifications.
Part D - Properties (Customary/Metric)
This Part is a supplementary book referenced by other sections of the Code. It provides tables for the design stress values, tensile and yield stress values as well as tables for material properties (Modulus of Elasticity, Coefficient of heat transfer et al.)
It has been suggested that this section be split out into another article titled ASME BPVC Section III - Rules for Construction of Nuclear Facility Components. (Discuss) (March 2023) |
Section III of the ASME Code Address the rules for construction of nuclear facility components and supports. The components and supports covered by section III are intended to be installed in a nuclear power system that serves the purpose of producing and controlling the output of thermal energy from nuclear fuel and those associated systems essential to safety of nuclear power system. Section III provides requirements for new construction of nuclear power system considering mechanical and thermal stresses due to cyclic operation. Deterioration, which may occur in service as result of radiation effects, corrosion, or instability of the material, is typically not addressed.
This section needs expansion. You can help by adding missing information. (March 2023) |
This section of the ASME BPVC contains the requirements for nondestructive examinations which are referred and required by other sections of the Code.
It also covers the suppliers examination responsibilities, requirements of the authorized inspectors (AI) as well as the requirements for the qualification of personnel, inspection and examinations.
It has been suggested that this section be split out into another article titled ASME BPVC Section VIII - Rules for Construction of Pressure Vessels. (Discuss) (March 2023) |
This section of the ASME BPVC consists of 3 divisions.
Div. 1 covers the mandatory requirements, specific prohibitions and nonmandatory guidance for materials, design, fabrication, inspection and testing, markings and reports, overpressure protection and certification of pressure vessels having an internal or external pressure which exceeds 15 psi (100 kPa). Pressure vessels covered by this division can be either fired or unfired. The pressure may be from external sources, or by the application of heating from an indirect or direct source, or any combination thereof.
The division is not numbered in the traditional method (Part 1, Part 2 etc.) but is structured with Subsections and Parts which consist of letters followed by a number. The structure is as follows:
This division covers the mandatory requirements, specific prohibitions and nonmandatory guidance for materials, design, fabrication, inspection and testing, markings and reports, overpressure protection and certification of pressure vessels having an internal or external pressure which exceeds 3000 psi (20700 kPa) but less than 10,000 psi.
The pressure vessels can be either fired or unfired. The pressure may be from external sources, or by the application of heating from an indirect or direct source as a result of a process, or any combination of the two.
The rules contained in this section can be used as an alternative to the minimum requirements specified in Division 1. Generally the Division 2 rules are more onerous than in Division 1 with respect to materials, design and nondestructive examinations but higher design stress intensity values are allowed. Division 2 has also provisions for the use of finite element analysis to determine expected stress in pressure equipment, in addition to the traditional approach of design by formula (Part 5: "Design by Analysis requirements").
This division covers the mandatory requirements, specific prohibitions and nonmandatory guidance for materials, design, fabrication, inspection and testing, markings and reports, overpressure protection and certification of pressure vessels having an internal or external pressure which exceeds 10,000 psi (70,000 kPa).
The pressure vessel can be either fired or unfired. The pressure may be from external sources, by the application of heating from an indirect or direct source, process reaction or any combination thereof.
Section IX – Welding, Brazing, and Fusing Qualifications establishes the qualification requirements for welding, brazing, and plastic fusing procedures and for the personnel performing these joining processes. Unlike most sections of the ASME Boiler and Pressure Vessel Code (BPVC), which prescribe fabrication requirements directly or specify design, inspection, and testing for components like boilers and pressure vessels, Section IX is primarily a referencing code. Its qualification requirements are not invoked independently but are instead called upon by other ASME construction codes (such as Section VIII for pressure vessels or B31 for piping).
Prior to the introduction of Section IX, individual sections of the BPVC contained their own separate and varying qualification requirements for welded construction. Following the formal acceptance of welding for pressure-retaining components in the 1935 edition of the Code (where it was initially introduced as a supplement to Section VIII), a joint committee of the American Society of Mechanical Engineers (ASME) and the American Welding Society (AWS) was established to develop a unified qualification standard.
Section IX was first published as a standalone section of the BPVC in 1941, initially covering only three welding processes: Shielded Metal Arc Welding (SMAW), Oxy-Fuel Welding (OFW), and Carbon-Arc Welding (CAW). The fundamental philosophy of qualifying procedures and personnel while permitting qualified ranges of variables has remained largely unchanged since this first edition. Although additional joining processes and qualification rules have been incorporated over time to keep pace with industrial technology, the core mechanics of the code have remained highly stable.
The scope of Section IX has expanded periodically over its history. Brazing qualifications were incorporated in the 1960 edition, turning it into the "Welding and Brazing Qualifications" standard. The 2013 edition introduced qualification requirements for plastic fusing, along with a common set of general requirements applicable to all material-joining processes.
For welding, Section IX establishes requirements for qualifying Welding Procedure Specifications (WPSs) by means of Procedure Qualification Records (PQRs) and for qualifying welders and welding operators through performance qualification tests. Similar qualification systems are provided for brazing procedures and brazers, and for plastic fusing procedures and operators.
A fundamental concept of Section IX is the classification of qualification variables as essential, supplementary essential, and nonessential variables:
To reduce the administrative and economic burden of procedure qualifications, Section IX groups base materials into P-Numbers and welding filler metals into F-Numbers. Qualification of a procedure using one material or filler metal may therefore extend to other materials or filler metals within the same classification, subject to the qualification rules of the Code.
Since the 2013 edition, Section IX has been organized into a modular structure consisting of four principal Parts:
Within Part QW, Article V is unique because it permits manufacturers and contractors to use prequalified Standard Welding Procedure Specifications (SWPSs) that have been developed by the American Welding Society (AWS) and formally adopted by ASME, bypassing the typical requirement for an organization to perform its own independent Procedure Qualification Record (PQR) testing.
Section IX is referenced by numerous ASME construction codes, including those governing boilers, pressure vessels, and pressure piping. Because of its rigorous framework and historical reliability, it is widely used internationally as the definitive qualification standard for joining procedures and personnel in pressure equipment fabrication, even in countries that do not otherwise utilize the ASME construction codes. Within ISO-based manufacturing systems, it serves a functionally parallel purpose to the ISO 15614 series (for procedure qualification) and the ISO 9606 series (for personnel qualification).