Rassvet (ISS module)

Rassvet

Rassvet as seen from the Cupola module during STS-132 with a Progress in the lower right
Module statistics
Part of	International Space Station
Launch date	14 May 2010, 18:20:09 UTC
Launch vehicle	Space Shuttle Atlantis
Berthed	18 May 2010, 12:20 UTC (Zarya nadir)
Mass	5,075 kg (11,188 lb)
Length	6 m (20 ft)
Diameter	2.35 m (7 ft 9 in)
Pressurised volume	Total: 17.4 m3 (610 cu ft) Pressurised: 5.85 m3 (207 cu ft)
References:

Rassvet (Russian: Рассвет, lit. 'first light'), also known as the Mini-Research Module 1 (MRM 1, Russian: Малый исследовательский модуль 1) and formerly known as the Docking Cargo Module, is a component of the International Space Station (ISS). The module's design is similar to the Mir Docking Module launched on STS-74 in 1995. Rassvet is primarily used for cargo storage and as a docking port for visiting spacecraft. It was flown to the ISS aboard Space Shuttle Atlantis on the STS-132 mission on 14 May 2010, and was connected to the ISS on 18 May 2010. The hatch connecting Rassvet with the ISS was first opened on 20 May 2010. On 28 June 2010, the Soyuz TMA-19 spacecraft performed the first docking with the module.

Details

Rassvet was berthed to the nadir port of Zarya with help from the Canadarm2. Rassvet carried externally attached (piggybacking) outfitting equipment for the future Nauka (Multipurpose Laboratory Module-Upgrade). That equipment included a spare elbow joint for the European Robotic Arm (ERA), an ERA portable workpost used during EVAs, heat radiator, internal hardware and Nauka's experiment airlock for launching cubesats. Delivering Rassvet thus enabled NASA to fulfill its promise to ship 1,400 kilograms (3,100 lb) to equip the Nauka.

Rassvet has two docking units: one to attach to the nadir port of the Zarya module and one to provide a docking port for a Soyuz or Progress spacecraft. It implements the role of the Docking and Storage Module from the original ISS design. Russia announced the cancellation of the last of the two planned Russian Research Modules when it announced the plans for Rassvet.

Initial planning

The initial ISS plan included a Docking and Storage Module (DSM). This planned Russian element was intended to provide facilities for stowage and an additional docking port and would have been launched to the station on a Proton launch vehicle. The DSM would have been mounted to Zarya's nadir (Earth-facing) docking port. It would have been similar in size and shape to the Zarya module.

The DSM was canceled due to Russian budgetary constraints for some time, but its design was eventually modified into the Docking and Cargo Module (Rassvet) that was to be connected to the same Zarya location to provide storage space and a docking port. During the cancellation period, it was proposed that a Multi-Purpose Module (MPM) called Enterprise should be docked to Zarya, and later the Nauka was proposed to be located there as well, but the Enterprise module has since been canceled and Nauka was docked to Zvezda's nadir port instead.

Purpose

Rassvet was designed as a solution to two problems facing the ISS partners:

• NASA was contracted to carry the Nauka outfitting equipment into space.^{[citation needed]}
• The overlapping missions of the Progress, Soyuz, and ATV spacecraft highlighted the need to have four Russian docking ports available on the ISS. The cancellation of both Russian Research Modules meant that the ISS would be left with just three such docking ports after the installation of the Leonardo module in 2011, which made the nadir port of Zarya unusable.^{[citation needed]}

Rassvet solved both of these issues. NASA did not need to add another payload flight to accommodate the Nauka outfitting equipment, as it could attach the hardware to the exterior of Rassvet.

The ISS now had four docking ports available on the Russian segment: the aft port of Zvezda, the port of Pirs, later Nauka (on the nadir port of Zvezda), the port of Poisk (on the zenith port of Zvezda), and the port on Rassvet (on the nadir port of Zarya). Russia's cancellation of the Research Module thus became less consequential for the ISS program as a whole.

Design and construction

The module was designed and built by Energia, from the already-made pressurized hull of the mock-up for dynamic tests of the cancelled Science Power Platform.

On 17 December 2009, an Antonov An-124 carrying the Rassvet Module and ground process equipment arrived at the Kennedy Space Center in Florida. Upon unloading, the equipment was delivered to a prelaunch processing facility run by the Astrotech. Energia specialists and technicians continued their work on the processing of the Rassvet module at the facility, completing stand-alone electrical tests and leak tests of the module and the airlock. They also prepared the airlock and the radiative heat exchanger for installation onto Rassvet. The module was moved to NASA's Space Station Processing Facility on 2 April 2010. After completing the final touches, it was placed into the shuttle payload transporter on 5 April 2010. The payload canister containing the Rassvet Module arrived at LC-39A on 15 April 2010.

Engineers at Launch Pad 39A preparing Space Shuttle Atlantis had noticed paint peeling from the Rassvet module. Although the problem was declared to have no impact on the operation of Rassvet, it posed a potential threat of releasing debris on orbit.

Visited spacecraft

Rassvet was connected to nadir port of Zarya on 18 May 2010. All visiting spacecraft have launched from Baikonur Cosmodrome.

Gallery

• 
  Diagram showing the Nauka components attached to Rassvet at launch
• 
  Rassvet at the Astrotech Facility
• 
  Rassvet module development
• 
  Rassvet module

See also

• Poisk (ISS module)
• Pirs (ISS module)

References

External links

Wikimedia Commons has media related to Rassvet (ISS module).

• http://space.skyrocket.de/doc_sdat/dsm.htm
• http://www.russianspaceweb.com/iss_enterprise.html
• Rassvet at Astrotech looking NW
• Rassvet at Astrotech looking north
• Rassvet at Astrotech from above
• Rassvet at Astrotech looking SE