



A plastic bottle is a bottle constructed from high-density or low-density plastic. They are typically used to store liquids such as water, soft drinks, motor oil, cooking oil, medicine, shampoo or milk. They range from very small bottles to large carboys. Consumer blow molded containers often have integral handles or are shaped to facilitate grasping.
Plastic was invented in the nineteenth century and was originally used to replace common materials such as ivory, rubber, and shellac. Plastic bottles were first used commercially in 1947, but remained impractical until the 1970s, when the PET bottle was introduced. They quickly became popular with manufacturers and customers because they are lighter, cheaper and easier to transport than glass bottles and less susceptible to corrosion than metal containers. However, their greatest advantage over glass bottles is their superior resistance to breakage, in both production and transportation. Except for wine and beer, the food industry internationally has largely replaced glass bottles with plastic bottles.
This section needs more citations. (October 2017) |

The materials used in the manufacture of plastic bottles vary by application.

The neck of a plastic bottle is the funnel through which liquid is added and removed. It normally features a standardized thread for screwing a screw cap on.
The 28 mm PET bottle neck finish used in almost all PET beverage bottles worldwide is standardized as PCO 1881 (where "PCO" stands for Plastic Closure Only) It was established as a voluntary guideline standard by the International Society of Beverage Technologists (ISBT), following industry collaborative design efforts initiated in 2007 and finalized in 2009. The PCO 1881 finish was engineered as a lightweight, short-neck successor to the older, taller PCO 1810 standard.
The total finish height is 17 mm, with a functional neck height of 13.5 mm. The plastic neck finish weight is 3.8 g. The finish utilizes interrupted threads that serve as vent slots. These allow carbon dioxide gas in the bottle to safely depressurize before the cap completely disengages during unscrewing. It features a relatively short thread engagement (about 1.5 to 1.75 turns).
While primarily designed for pressurized carbonated soft drink (CSD) and sparkling beverage containers, the PCO 1881 standard has also been adopted across still water and juice production lines to unify packaging machinery and supply chain requirements.
There is ongoing concern as to the use of plastics in consumer food packaging solutions, environmental impact of the disposal of these products, as well as concerns regarding consumer safety. Karin Michaels, Associate Professor at Harvard Medical School, suggests that toxins leaching from plastics might be related to disorders in humans such as endocrine disruption. Aluminum and cyanide were found as trace elements in the examined samples, which are considered to be toxic elements according to the American FDA. In the United States, plastic water bottles are regulated by the FDA, which also inspects and samples bottled water plants periodically. Plastic water bottle plants hold a low priority for inspection due to a continuously good safety record. In the past, the FDA maintained that there was a lack of human data showing plastics pose health problems. However, in January 2010, the FDA reversed its opinion saying they now have concerns about health risks.
It is a common misconception that drinking from plastic water bottles increases cancer risk; there is no such risk.
An article published on 6 November 2017 in Water Research reported on the content of microplastics in mineral waters packed in plastic or glass bottles, or beverage cartons. In 2018, research conducted by Sherri Mason from the State University of New York in Fredonia[where?] revealed the presence of polypropylene, polystyrene, nylon and polyethylene terephthalate microparticles in plastic bottles. Polypropylene was thereby found to be the most common polymeric material (54%) and nylon the second most abundant (16%) polymeric material. The study also mentioned that polypropylene and polyethylene are polymers that are often used to make plastic bottle caps. Also, 4% of retrieved plastic particles were found to have signatures of industrial lubricants coating the polymer. The research was reviewed by Andrew Mayes of the University of East Anglia (UEA) School of Chemistry The European Food Safety Authority suggested most microplastics are excreted by the body; however, the Food and Agriculture Organization, a specialised agency of the United Nations, warned that it is possible that the smallest particles (< 1.5 μm) could enter the bloodstream and organs, via the intestinal wall. Microplastics have been observed to cross the blood-brain barrier, found in semen, testes, and placenta tissue.

Plastic bottles are marked at their base with the resin identification code to indicate the material used.[self-published source?]
Product labels are attached with adhesive or are shrunk to fit. In-mould labelling is a process of building the label into the bottle during molding.
An accordion bottle or collapsible bottle is a plastic bottle designed to store darkroom chemicals or any other chemical that is highly susceptible to oxidation. They work by being able to squeeze down to remove excess air from the bottle to extend the life of the product. An alternate benefit is minimizing storage, transportation, or disposal space when the bottle is empty or as the content is being dispersed, for example with water bottles used by hikers. Collapsing can also keep foods fresher.
Bottles, used for storing carbonated water and soft drinks, has an uneven bottom for stability reasons. The technology was developed and patented by Domas Adomaitis in the United States in 1971.
Although carbonated soda bottles were designed for holding beverages, they have been used for other purposes. For example, in poor countries, empty two-liter soda bottles have been reused as an improvised personal flotation device to prevent drowning.