This article needs more citations. (January 2021) |
A reactor protection system (RPS) is a set of nuclear safety and security components in a nuclear power plant designed to safely shut down the reactor and prevent the release of radioactive materials. The system can "trip" automatically (initiating a scram), or it can be tripped by the operators. Trips occur when the parameters meet or exceed the limit setpoint. A trip of the RPS results in full insertion (by gravity in pressurized water reactors or high-speed injection in boiling water reactors) of all control rods and shutdown of the reactor.
The RPS provides a first line of automatic protective response to both anticipated operational occurrences and postulated accident conditions, by detecting abnormal conditions and initiating reactor trip and other protective actions that help preserve core and pressure-boundary integrity. In advanced reactor I&C frameworks, the RPS may also provide additional post-trip functions to support continued heat removal after shutdown.
Because protective actions depend on timely and reliable detection and actuation, the RPS is tightly coupled to plant sensors and actuators and is treated as among the most safety-significant subsystems in safety analyses.
RPS actuation logic is configured around measured process variables (trip variables) and setpoints derived from safety analysis, including fuel and thermal-hydraulic design limits. In order to ensure reliability, the RPS often employs multi-channel redundancy combined with voting logic to reduce spurious trips. One common configuration is four channels with 2-out-of-4 trip logic.
Independence among redundant channels is emphasized as a design principle to mitigate random single failures and certain classes of common-cause vulnerabilities. However, while redundancy and independence can mitigate some failures, they may not address all systematic failures such as during natural disasters.
Digitization of safety I&C has been pursued to address obsolescence and to realize functional advantages such as improved diagnostics, but it also introduces new challenges, especially software failure and increased system complexity. As functionality now depends on extensive software, strict verification and validation (V&V) practices for safety-critical code are emphasized. In a typical RPS software workflow, protection software is specified, designed in function-block or ladder-logic representations, translated into C code, and compiled for programmable logic controllers (PLCs).
A variety of reliability modeling approaches are used for RPS software evaluation. Dynamic fault tree (DFT) modeling has been proposed to better capture changes in effective k-out-of-n logic caused by periodic testing and maintenance, addressing limitations of static fault trees in representing time-dependent configurations in RPS safety analysis. Markov-based methods remain common for but may face scalability challenges.
Increasing digitization of RPS and other safety I&C has elevated the importance of cybersecurity controls for systems whose compromise could affect protective functions. Nuclear power plant cybersecurity measures emphasize a defense-in-depth model, including identification of critical digital assets, risk assessment, threat modeling, and establishment of layered protections.
Some of the measured parameters for US pressurized water plants would include:
Each parameter is measured by independent channels such that actuation of any two channels would result in an automatic SCRAM or reactor shutdown. The system also allows manual actuation by the operator. The control rods are held by a fail-safe electromagnetic mechanism: tripping the reactor cuts power to it, so that all of the rods drop into the core under gravity.
The RPS in a boiling water reactor design consists of 4 separate divisions. Each division has its own set of sensors, trip logic and trip devices. Each channel senses the process parameters within the plant and if a parameter exceeds its defined trip point, an on/off signal will be sent to each of the 4 divisions of trip logic. A reactor scram can only be achieved by having 2 or more trip conditions in any of the 4 automatic trip channels. This means it uses 2 out of 4 coincidence logic so there is an appropriate balance between preventing false trips and ensuring a fast response.
The General Electric BWR RPS has four main components, the sensor channels, the trip system, the hydraulic control units (HCUs) and their associated components and the control rods. The trip system has two trip trains, train A & B. Each trip train is fed from two channels; train A from channels A & C and train B from channels B & D. A scram signal will be initiated when at least one sensor from train A and one sensor from train B identifies a scram condition, this is known as one out of two twice logic. Most BWR designs have around 120-190 control rods with associated control rod drives (CRDs). Each pair of control rods is driven by an individual HCU which contains a high pressure pre-charged scram accumulator.
On receipt of a SCRAM signal the RPS de-energises the solenoid valves in each HCU, allowing the compressed air supply to be removed from the SCRAM valves thus allowing the hydraulic energy stored in the SCRAM accumulators to rapidly move the control rods upwards into the reactor core. This system is fail safe so if there is a failure of electric supply to the solenoid valves or the control air pressure, a SCRAM will occur. There is an additional SCRAM system by opening the air header dump valves to allow the pressure to be released in the SCRAM air header.
The following conditions cause a reactor scram in BWRs. High reactor pressure, low reactor water level (Level 3), high reactor water level (Level 8), isolation valve closure in main steam line during power operation, high drywell pressure, high suppression pool temperature, low scram accumulator charging water header pressure, turbine stop valve closure, fast turbine control valve closure, and neutron monitoring system. Reactor scram can also be manually initiated by using scram switches and the reactor mode switch. This is independent of the automatic sensor channel logic.
While much of historical RPS development is rooted in large light-water reactor practice, RPS concepts and design requirements also appear in advanced and smaller reactors. For example, digital RPS development has also been documented for high-temperature gas-cooled reactors (HTGRs).