Nikon Z-mount

Nikon Z-mount
TypeBayonet
Inner diameter55 mm
Tabs4
Flange16 mm
Connectors11 electrical pins
Introduced2018
ReplacedNikon 1 series
Nikon Z6 showing wide-diameter lens mount and full-frame sensor

Nikon Z-mount (stylized as ℤ) is an interchangeable lens mount developed by Nikon for its mirrorless digital cameras.

When it was announced on August 23, 2018, Nikon released:

With the introduction of the Z-mount, Nikon discontinued its previous mirrorless mount, the Nikon 1 series.

Z-mount characteristics

Throat diameter

The 55 mm throat diameter of the Nikon Z-mount makes it the largest full-frame lens mount. It is much larger than the older Nikon F-mount (44 mm) and than the Sony mirrorless E-mount (46.1 mm), but only slightly larger than the 54 mm of both the Canon EF and RF mounts and of the 51.6 mm diameter full-frame mirrorless Leica L-Mount.

Flange distance

The Z-mount has a very short flange distance of 16 mm, which is shorter than all previously mentioned lens mounts. The shorter flange distance allows Nikon (and others) to build smaller and simpler lenses.

This flange distance, along with the large throat diameter, allows for numerous lenses of nearly all other current and previous mounts to be used with an appropriate lens mount adapter on a Z-mount camera (see Mount adapters for a list of mounts and adapters).

Lens contacts

The number of electrical contacts between the camera body and lens was increased from eight (on the F-mount) to eleven (on the Z-mount). These communicate lens information to the camera and provide power and instructions to the lens from the camera. There are no mechanical levers or plungers for communicating information.

Mount type and tabs

As on most interchangeable lens mount camera systems, the Z-mount uses a bayonet mount for attaching the lens to the camera. Nikon increased the number of tabs from three (on the F-mount) to four. This provides slightly more security on the mounted lens.

Lens formats: FX and DX

For its two sensor sizes, FX (Full-frame) and DX (APS-C), Nikon develops two varieties of lens. The two versions both use the Z-mount, and are mechanically and electronically identical. When mounted on the same camera type (i.e., an FX lens on an FX camera or a DX lens on a DX camera), a lens performs according to its nominal characteristics. When a DX lens is mounted on an FX camera, it causes the camera to use a crop mode from the center of the sensor, corresponding to the DX coverage of the lens. When an FX lens is mounted on a DX camera, it provides a 1.5x crop field of view, as is typical with an APS-C camera.

Lens mounting

Z-mount lenses lock (i.e., attach to the camera) by aligning the white dots on the camera body and lens and turning the lens counter-clockwise (when looking at the front of lens) until it clicks, signifying that it is locked. To unlock, the camera's Lens Release button is pressed and the lens is rotated clockwise.

Z-mount cameras

Introduction of the cameras

In late 2018, Nikon released the first two cameras (alongside three lenses and the FTZ adapter) that use this mount, the full-frame Nikon Z7 and Nikon Z6, both using the then top‑of‑the‑line Expeed 6 image processor. In late 2019 Nikon announced their first Z-mount camera with an APS-C sensor, the Nikon Z50, also using the Expeed 6. In July 2020 the entry-level full-frame Z5 was introduced. In October 2020, Nikon announced the Nikon Z6II and Nikon Z7II, which succeed the Z6 and Z7, respectively. Both used dual Expeed 6 image processors. The APS-C lineup was expanded in July 2021, with the introduction of the retro-styled Nikon Zfc.

In October 2021, Nikon unveiled the Nikon Z9, which effectively succeeded the brand's flagship D6 DSLR. It was the first to use the Expeed 7 processor. The APS-C lineup was further expanded with the Nikon Z30, announced at the end of June 2022. 2023 brought the introduction of the Z8 and Zf, the second and third cameras to use the Expeed 7. The Nikon Z6III was announced in June 2024. In November 2024, Nikon announced the Z50II as a major upgrade of the Z50; it became the first APS-C camera to use the Expeed 7 processor introduced with the Z9. In April 2025, Nikon announced the Z5II as a major upgrade for its lowest class full-frame line of cameras. In September 2025, Nikon announced the first camera of its "Z Cinema" line, the ZR, co-designed with RED. The ZR is the first Nikon camera that internally offers the 12-bit R3D NE raw video codec (Redcode Raw with TicoRAW). In September 2026, Nikon announced the full-frame Z5IIC, stating that it has “user-friendly features for first-time mirrorless camera users.”

Camera overview

The following table contains the specifications for all sixteen Nikon Z-mount cameras, including models that have been discontinued. The three Red cinema cameras with Z-mounts are shown in the following section.

All Z-mount cameras can use all Z-mount lenses, operating as described in Lens formats. In addition, they can also use Nikon F-mount lenses through the use of an FTZ II adapter.

Camera Years Sensor LCD
EVF
Card
slots
Continuous
release fps
Wt.
g
Video fps Video color depth Ref
Type
Model
Intro
Disc
Type
Size
Z30 2022   20.9 B No 3.0" 1.04 M No 6 SD 11 405 120 30 n/a n/a Yes No No
Z50 2019 2024 20.9 B No 3.2" 1.04 M Yes 6 SD 11 450 120 30 n/a n/a Yes No No
Z50II 2024   20.9 B No 3.2" 1.04 M Yes 7 SD 11
30 (JPEG)
550 120 30
60
n/a n/a Yes Yes No
Zfc 2021   20.9 B No 3.2" 1.04 M Yes 6 SD 11 445 120 30 n/a n/a Yes No No
Z5 2020   24.3 B Yes 3.2" 1.04 M Yes 6 SD ×2 4.5 675 60 30 No n/a Yes No No
Z5II 2025   24.5 B Yes 3.2" 2.10 M Yes 7 SD ×2 11
30 (JPEG)
700 120 30
60
No n/a Yes Yes RAW:
Z5IIC 2026   24.5 B Yes 3.2" 2.10 M No 7 SD 11
30 (JPEG)
620 120 30
60
No n/a Yes Yes RAW:
Zf 2023   24.5 B Yes 3.2" 2.10 M Yes 7 SD +
microSD
14 710 120 30
60
No n/a Yes Yes No
Z6 2018 2022 24.5 B Yes 3.2" 2.10 M Yes 6 CFX 12 675 120 30 No n/a Yes HDMI
Upgrade
Z6II 2020   24.5 B Yes 3.2" 2.10 M Yes 6×2 CFX +
SD
14 705 120 30
60
No n/a Yes HDMI
Upgrade
Z6III 2024   24.5 P Yes 3.2" 2.10 M Yes 7 CFX +
SD
20 (RAW)
60 (JPEG)
120 (11 MP)
760 240 60
120
60 n/a Yes Yes RAW:
ZR 2025   24.5 P Yes 4.0" 3.07 M No 7 CFX +
microSD
20 (RAW)
60 (JPEG)
120 (11 MP)
630 240 60
120
60 n/a Yes Yes RAW:
Z7 2018 2022 45.7 B Yes 3.2" 2.10 M Yes 6 CFX 9 675 120 30 No No Yes HDMI
Upgrade
Z7II 2020   45.7 B Yes 3.2" 2.10 M Yes 6×2 CFX +
SD
10 705 120 30
60
No No Yes HDMI
Upgrade
Z8 2023   45.7 S Yes 3.2" 2.10 M Yes 7 CFX +
SD
20 (RAW)
30 (JPEG)
60 (19 MP)
120 (11 MP)
910 120 120 No 60 Yes Yes RAW:
Z9 2021   45.7 S Yes 3.2" 2.10 M Yes 7 CFX ×2 20 (RAW)
30 (JPEG)
60 (19 MP)
120 (11 MP)
1340 120 120 No 60 Yes Yes RAW:
Notes
  1. ↑ Sensor Info
    MP - Megapixels
    Type of imaging sensor
      S - Stacked BSI
      P - Partially Stacked BSI
      B - BSI
    Stabilized or not
  2. ↑ All SD card slots are UHS-II, except for the Z30, Z50, and Zfc, which are UHS-I.
    All microSD slots, as on the Zf and ZR, are UHS-I.
  3. ↑ CFX (CFexpress) card slots are backwards-compatible to XQD cards.
  4. ↑ If a video recording mode results in a crop, it is given as a footnote after the fps value.
  5. ↑ The supported video frame rates are: 24/25/30 fps when up to 30 fps are supported, while cameras supporting up to 60 fps also support 50 fps recording. Cameras supporting up to 120 fps also support 100 fps recording. Cameras supporting 100/120 fps recording can also record in x4/x5 slow motion directly (targeting 24/25/30 fps video frame rates), which means playback of the resulting video file is already in slow motion, without the need for editing.
  6. ↑ The Z50, Zfc, Z5, Z6, Z6II, Z7, and Z7II have a 30-minute length limitation for internal recording; all others have longer durations, which vary by settings. External recording time for all camera is only limited by battery life.
  7. ↑ In 6K & 8K,
    "no" means camera theoretically could, but does not support;
    "n/a" means camera doesn't have enough pixels to support
  8. 1 2 3 4 5 6 7 At this frame rate, there is a 1.5× crop.
  9. ↑ At this frame rate, there is a 1.7× crop.
  10. 1 2 3 4 5 6 The camera's 12-bit video recording supports the Raw format N-RAW.
  11. 1 2 3 4 10-bit output can be recorded with an external HDMI recorder. External 10-bit recording can optionally use N-Log, a profile for recording video. The Z6II, Z6III, and Z7II also support external recording of 10-bit hybrid log gamma (HLG) video.
  12. 1 2 3 4 12-bit output requires a compatible recorder and is a paid upgrade. The extra-cost 12-bit upgrade enables external recording of 12-bit ProRes RAW. The resulting footage has greater dynamic range than 8- or 10-bit footage. However, the camera uses pixel skipping (which is necessary since ProRes RAW directly stores non-debayered sensor data) resulting in a somewhat softer image with more noise and more frequent appearance of moiré patterns compared to the full-width downsampling 8- and 10-bit modes.
  13. 1 2 3 4 The camera's 12-bit video recording supports the Raw format ProRes RAW HQ.
  14. ↑ The camera's 12-bit video recording supports the Raw format R3D NE.
  15. ↑ At this frame rate, there is a 1.08× crop.

Red cinema cameras

In 2024, Red Digital Cinema was acquired by Nikon. On 12 February 2025, the first two cinema cameras using the Z-mount, the V-RAPTOR [X] and the KOMODO-X, were released. On 9 September 2025, Red released the V‑RAPTOR XE, also offering a Z-mount version besides the RF-mount variant. Along with the ZR, they are all part of the Z Cinema line.

Red cinema cameras with a Z-mount can use all Z-mount lenses, although some lenses may have greater than normal distortion and/or light falloff, as the VV sensor is slightly wider than an FX sensor. In addition to Z-mount lenses, Red cinema cameras can also use Nikon F-mount lenses through the use of an FTZ II adapter, with the same issues as Z-mount lenses.

The following table contains the specifications for the three Nikon Red Z-mount cameras:

RED Digital Cinema cameras using Z-mount
Model Intro Sensor Ref
Size Res Shutter
RED V-RAPTOR [X] Z mount 2025 VV/LF 8K Global shutter
RED KOMODO-X Z mount 2025 Super 35 6K Global shutter
RED V-RAPTOR XE Z mount 2025 VV/LF 8K Global shutter

Z-mount lenses

With the introduction of the Z-mount, Nikon began designing and releasing a new set of lens for that mount. For its two sensor sizes, FX (Full-frame) and DX (APS-C), Nikon develops two varieties of lens. The two versions both use the Z-mount, and are mechanically and electronically identical. When mounted on the same camera type (i.e., an FX lens on an FX camera or a DX lens on a DX camera), a lens performs according to its nominal characteristics. When a DX lens is mounted on an FX camera, it causes the camera to use a crop mode from the center of the sensor, corresponding to the DX coverage of the lens. When an FX lens is mounted on a DX camera, it provides a 1.5x crop field of view, as is typical with an APS-C camera.

Nikon published a roadmap outlining forthcoming lenses when the Z-mount system was initially announced. The roadmap has been updated multiple times. As of February 2025, all lenses in the last version of the roadmap from September 2023 were released. Several lenses which were not indicated on the roadmap were released as well.

In 2018, Nikon announced the development of the Z-mount 58 mm f/0.95 S Noct lens, reintroducing the Noct brand, which was historically used by Nikon for lenses with ultra-fast maximum apertures. The lens was released in October 2019.

On 30 October 2024, Nikon announced that it was developing a video-centric, standard zoom lens with power zoom, the NIKKOR Z 28-135mm f/4 PZ. On 13 February 2025, the details of the lens were released, alongside the announcement of the first two RED Digital Cinema cinema cameras with Z-mounts, the V-Raptor [X] and Komodo-X.

On 12 September 2025, Nikon teased and confirmed the development of a line of "Z Cinema" lenses, without disclosing specific lens series or model details. Half a year later, on 19 April 2026, Nikon published a video teaser for the lens series. On 8 September 2026, the company confirmed nine T1.9 cinema lenses covering a range of focal lengths, all part of the "Nikkor Z Cinema T1.9 VV" series. The lenses are featuring an image circle larger than full-frame, that can cover the V-Raptor [X] VV sensor (40.96 mm × 21.60 mm). At the time of the announcement, out of the nine lenses, the first and only lens model confirmed is the Nikkor Z Cinema 50mm T1.9 VV.

Lens designations

All of Nikon's Z-mount lenses are Nikkors, which has been Nikon's brand for their lenses since 1932.

In their labeling of lenses, each lens shows two numbers, giving the focal length and aperture.

  • The focal length (in mm) is listed first (before the aperture) and is shown as either just a number (e.g., "35") or a number followed by an mm (e.g., "105mm").
  • This is followed by the aperture value(s), with one of the following used, based on the specific lens and its characteristics:
    • F-stop: aperture number (e.g., "1.9") or range of numbers (e.g., "3.5-6.3") is shown.
    • T-stop: aperture number starting with a T followed by the aperture number (e.g., "T1.9").

In addition to the focal length and aperture, Nikon uses a new designation system (i.e., various tags) for their Z-mount lenses. The older F-mount Nikkor designations are no longer used, though they overlap in some areas (e.g., the VR and DX labels). Of particular interest, Nikon introduced the S (for S-Line) branding for especially high-performance ("superior") lenses, which is akin to Canon's L designation or Sony's G or GM branding.

Lens lines

The Nikkor Z line-up has several distinct lines of lenses, which are designed with similar handling and optical characteristics.

Nikkor Z lens lines
LineLensesDescription
Holy Trinity
  • Nikkor Z 14–24 mm f/2.8 S
  • Nikkor Z 24–70 mm f/2.8 S II
  • Nikkor Z 70–200 mm f/2.8 VR S II
Professional S-Line f/2.8 zooms
Economical Trinity
  • Nikkor Z 17–28 mm f/2.8
  • Nikkor Z 28–75 mm f/2.8
  • Nikkor Z 70–180 mm f/2.8
These are adapted Tamron designs offering less wide-angle, less reach and no VR, but at a substantially lower cost. Due to this trade-off, they are not part of the S-line.
Lightweight Trinity
  • Nikkor Z 14–30 mm f/4 S
  • Nikkor Z 24–70 mm f/4 S
  • Nikkor Z 24–120 mm f/4 S
A series of S-Line f/4 zoom lenses covering the ultra-wide to tele range.
Compact Primes
  • Nikkor Z DX 24 mm f/1.7
  • Nikkor Z 26 mm f/2.8
  • Nikkor Z 28 mm f/2.8 SE
  • Nikkor Z 28 mm f/2.8
  • Nikkor Z 40 mm f/2
  • Nikkor Z 40 mm f/2 SE
Emphasizing smaller size and portability
Ultra-fast Primes
  • Nikkor Z 35 mm f/1.2 S
  • Nikkor Z 50 mm f/1.2 S
  • Nikkor Z 85 mm f/1.2 S
The f/1.2 S line of ultra-fast primes feature almost identical size and weight and all have the same 82mm filter size.
Fast Primes
  • Nikkor Z 35 mm f/1.4
  • Nikkor Z 50 mm f/1.4
The f/1.4 line of fast primes are designed for hybrid (photo/video) shooters; these lenses have characteristic rendering instead of perfect aberration control as implemented in the S-line lenses.
Superior Primes
  • Nikkor Z 20 mm f/1.8 S
  • Nikkor Z 24 mm f/1.8 S
  • Nikkor Z 35 mm f/1.8 S
  • Nikkor Z 50 mm f/1.8 S
  • Nikkor Z 85 mm f/1.8 S
  • Nikkor Z 135 mm f/1.8 S Plena
The f/1.8 S line of primes are known for superior image quality
Premium Super-Telephoto
  • Nikkor Z 400 mm f/2.8 TC VR S
    (integrated 1.4x teleconverter)
  • Nikkor Z 400 mm f/4.5 VR S
  • Nikkor Z 600 mm f/4 TC VR S
    (integrated 1.4x teleconverter)
  • Nikkor Z 600 mm f/6.3 VR S PF
  • Nikkor Z 800 mm f/6.3 VR S PF
All of these lenses have the same control scheme and the same set of lens control buttons.

Teleconverters

TC-2.0x teleconverter

The Nikon Z-mount teleconverters are a group of full-frame, secondary magnifying lenses mounted between the Z-mount lens and camera bodies to increase the focal length. It is attached to the Z-mount end of the lens before attaching the teleconverter's Z-mount to the powered-off camera. The following Nikon teleconverters are available:

Nikon Z-mount teleconverters
Name E/G Diam. × Len. Weight Change in speed Rel
date
Ref
Nikon Z TC-1.4x 6/4 72×18.5 mm
(2.8×0.7 in)
220 g
(7.8 oz)
Reduced by 1 stop 2020-08-28
Nikon Z TC-2.0x 8/5 72×32.5 mm
(2.8×1.3 in)
270 g
(9.5 oz)
Reduced by 2 stops 2020-08-28

The Nikon Z-mount teleconverters are only compatible with the following Nikon Z lenses, as the design of the lens must be able to physically accept the attachment of the Z teleconverter: There is a large protruding portion on the side of the teleconverter that attaches to the lens; many lenses don't have a recess which will accept this.

Zoom

  • Nikkor Z 70–180 mm f/2.8
  • Nikkor Z 70–200 mm f/2.8 VR S
  • Nikkor Z 70–200 mm f/2.8 VR S II
  • Nikkor Z 100–400 mm f/4.5–5.6 VR S
  • Nikkor Z 120–300 mm f/2.8 TC VR S
  • Nikkor Z 180–600 mm f/5.6–6.3 VR

Prime

  • Nikkor Z 400 mm f/2.8 TC VR S
  • Nikkor Z 400 mm f/4.5 VR S
  • Nikkor Z 600 mm f/4 TC VR S
  • Nikkor Z 600 mm f/6.3 VR S
  • Nikkor Z 800 mm f/6.3 VR S

Although the Z-mount teleconverters are full-frame, they can be used on a Z-mount DX camera with any of the preceding lenses, as all Z-mount lenses are usable on all Z-mount cameras.

Z-mount teleconverters cannot be mounted on top of each other, although they can be used on lenses that have built-in teleconverters (included in the preceding list with the letters "TC"), further extending their reach.

Relating to the use of teleconverters with an FTZ II (or FTZ) mount adapter:

  • Nikon Z-mount teleconverters cannot be used in conjunction with the FTZ adapter.
  • Nikon F-mount teleconverters can be used on compatible F-mount lenses when used with the FTZ adapter.

Nikon Z-mount adapters

Nikon has two types of Z-mount adapters:

Nikon Z-mount adapters for all Z-mount cameras

FTZ: Nikon F to Z-mount adapter, first generation

Nikon makes two lens adapters, the FTZ II and the original FTZ (discontinued in late 2021) which allow many Nikon F-mount lenses to be used on Z-mount cameras, including the RED Z-mount cameras. Nikon SLR cameras, both film and digital, have used the Nikon F-mount with its 44 mm throat diameter and 46.5 mm flange since 1959, while the Z-mount has a 55 mm throat diameter and a 16 mm flange distance. The FTZ allows AF-S, AF-P and AF-I lenses to autofocus on Z-mount cameras. The older screw-drive AF and AF-D lenses will not autofocus with the FTZ adapter (although some third-party adapters do support autofocus with screw-drive AF lenses), but they do retain metering and Exif data. All Z-mount cameras support metering with manual focus lenses, along with all full-frame Z-mount cameras also providing in-body image stabilization (IBIS) on them.

Mount adapters made by Nikon to support F-mount lenses on their Z-mount cameras are:

  • Nikon FTZ: The FTZ supports F-mount lenses on Z-mount cameras, and provides an integrated tripod foot. Metering, IBIS and Exif metadata are supported with any F-mount lens, including manual lenses, while autofocus is only supported with AF-I, AF-S and AF-P lenses. Variable autofocus speed for video shooting is only supported with AF-P and select AF-S lenses. The FTZ adds 30.5 mm to the length of the attached lens, which is the difference in flange distance between the Nikon F-mount (46.5 mm) and the Z-mount (16 mm), along with allowing the F's smaller throat diameter to be mated to the larger Z diameter. This model was announced along with the Z6 and Z7 in September 2018, and was discontinued by Nikon in October 2021, after the introduction of the FTZ II.
  • Nikon FTZ II: Same performance as the FTZ, but without the integrated tripod foot. This model was introduced in October 2021 along with the Z9, and allows for easier vertical shooting with the Z9.

As the FTZ adapter is a short, hollow tube with no lenses in its construction, there is no reduction in light passing through it, meaning no change in speed (unlike a teleconverter).

An FTZ adapter is attached to and released from a powered-off camera in the same manner as a lens. Once it is attached, the F-mount lens can then be attached to the adapter. Note that the FTZ has a lens release button for releasing an attached lens, similar to that on a camera body.

F-mount lens compatibility

Through the use of the FTZ, Nikon specifies F-mount lens compatibility as in the following table. Nikon F-mount teleconverters can be used on compatible F-mount lenses, but the Z-mount teleconverters may not be used in conjunction with the FTZ. For details on the lens types listed in the table, refer to Nikon F-mount.

Lens type Focus Exposure mode Metering mode IBIS Exif data
Autofocus
AF-P
AF-S
AF-I
Autofocus All modes (shutter-priority, aperture-priority, manual, and program modes) All modes (matrix, center-weighted, spot, and highlight-weighted metering) Yes Yes
G- and D-type (without motor) Manual focus
(with focus confirmation)
Other AF
(screw drive)
Manual focus
(with focus peaking and electronic rangefinder confirmation)
Manual focus
AI-P
PC-E
AI
PC
(no CPU contacts)
Aperture-priority and manual All modes, except highlight-weighted metering Focal length and maximum aperture need to be entered manually
Pre-AI Not officially supported.

Nikon Z-mount adapters for RED Z-mount cameras

Mount adapters provided by Nikon to support PL-mount lenses on their RED Z-mount cameras are the following:

  • RED Z to PL Adapter Pack: Enables the use of PL-mount lenses on Z-mount RED Digital Cinema cameras.
    There is no change in optical speed (T-stop or light transmission) when using this adapter, as it has no glass elements.
  • RED Z to PL with Electronic ND Adapter Pack: Similar to the previous, but includes an integrated electronic ND feature which allows a user to rapidly adjust exposure in 1/4, 1/3, or full stops.
    When the clear glass filter is installed in the adapter, there is no light loss or change in speed. When using the built-in ND filter cartridge, there is a reduction in exposure (in a 2-7 stop range, depanding on the setting).

Note that the two RED Z camera adapters cannot be used with Nikon Z mirrorless cameras, including the ZR.

Regarding PL lens, the RED Support page says the while "the vast majority of PL lenses are compatible with the PL Adapters w/ Electronic ND Filter, a small selection of PL lenses are not compatible due to their rear protrusion depth."

Third-party lenses and adapters

Three companies license the Z-mount from Nikon, enabling full compatibility and respecting intellectual property: Cosina Voigtländer, Sigma, and Tamron.

Numerous manufacturers offer purely manual lenses and lens mount adapters for the Z-mount, which do not interface electronically to the camera and do not support autofocus or automatic control of the aperture. Some manufacturers offer lenses and adapters with full electronic functionality (autofocus, automatic aperture control, Exif metadata, etc.). Other than the three companies listed previously, third-party lenses and adapters often rely on reverse engineering the electronic protocol of a lens mount and might not work properly on new cameras or new camera firmware versions.

Autofocus lenses

All of the third-party autofocus Z-mount lenses are shown in the Table of Z-mount lenses.

Note that collecting all specifications for third-party manual focus lenses isn't feasible due to the large number of brands producing a great variety of such lenses. However, some special-use manual focus lenses (perspective control and fisheye) are contained in the tables in the Other non-AF lenses section.

Third-party teleconverters

There is a third-party teleconverter from Viltrox made for the Nikon Z-mount:

  • Viltrox Teleconverter TC-2.0X Z — a 2.0× teleconverter

It is compatible with the following Nikkor lenses:

Zoom

  • Nikkor Z 70–200 mm f/2.8 VR S
  • Nikkor Z 100–400 mm f/4.5–5.6 VR S

Prime

  • Nikkor Z 400 mm f/4.5 VR S

Mount adapters

As described earlier, the short Z-mount flange distance coupled with the large throat diameter allows for numerous lenses of nearly all other current and previous mounts to be used with an appropriate lens mount adapter on a Z-mount camera.

  • For ARRI PL-mount lenses
    • The Wooden Camera Nikon Z Mount to PL Mount Adapter (Pro) can mount a PL lens.
    • The KipperTie Adapta v2 Z/PL converts from a Z-mount to industry-standard PL.
    • The Peipro PL-Z Lens Adapter lets you attach ARRI PL-mount cinema lenses onto Nikon Z-mount cameras.
    • The Viltrox PL-Z Lens Mount Adapter is designed to enable PL mount lenses to be used with Nikon Z-mount cameras.
  • For Canon EF lenses
    • The Fringer EF-NZ adapter provides full electronic integration (autofocus, image stabilization, aperture control).
    • The Fringer EF-NZ II revision removes the tripod foot for better handling with vertical grips (much like Nikon's FTZ II did) and adds weather-sealing.
    • The Techart TZC-01 also provides full electronic integration.
    • The Viltrox EF-Z adapter appears identical to the Fringer EF-NZ.
    • The Viltrox EF-Z2 has a built-in 0.7x focal reducer ("speed booster").
    • The Megadap EFTZ21 provides full electronic integration and autofocus, with an extra configurable control ring and a lens function button (L-Fn).
  • For Canon FD/FL lenses
    • The Fotodiox Pro FD-NKZ-P is an all-metal lens mount adapter that allows you to attach vintage Canon FD and FL 35mm SLR lenses.
    • The K&F Concept FD-NIK Z (KF06.366) lets you mount Canon FD and FL film lenses onto Z-mount cameras.
    • The Metabones Canon FD Lens to Nikon Z-mount T Adapter is a mechanical lens mount adapter that lets you mount Canon FD and FL lenses onto Z-mount cameras.
  • For Contax G lenses
    • The Techart TZG-01 adapts Contax G lenses with mechanical autofocus to Nikon Z. The Contax G system is somewhat similar to the older screw-drive Nikon AF system, but unlike the Nikon system, Contax G lenses do not have a manual focus ring. This makes Contax G unusually difficult to adapt to mirrorless cameras. It is not compatible with the Nikon Z9 and Z8.
    • The Shoten GTZ, similarly to the Techart TZG-01, adapts Contax G lenses with mechanical autofocus. It also has a micro-USB port on the bottom for firmware upgrades.
  • For Fujifilm G/GF/GFX lenses
    • The Boryoza GF to Nikon Z Autofocus Adapter lets you mount medium-format Fujifilm GFX lenses onto Nikon Z-mount mirrorless cameras with electronic communication and autofocus support.
    • The SHOTEN GXTZ is an electronic mount adapter that allows Fujifilm GFX medium-format GF-mount lenses to be mounted and used on Z-mount cameras.
  • For Fujifilm X mount lenses
    • The Boryoza XF-Z adapts Fujinon XF lenses with autofocus to Nikon Z.
  • For Leica M mount lenses
    • The Fotodiox LM-NKZ-PRN is an autofocus Leica M to Z adapter.
    • The Megadap MTZ11 contains a focusing helicoid with 6.5 mm of extension which is used for autofocus. This range is sufficient to cover the full focusing range of lenses up to around 50 mm focal length.
    • The Techart TZM-01 is similar to the Megadap MTZ11 and enables autofocus with M-mount lenses.
    • The Techart TZM-02 is a refined version of the TZM-01 with better autofocus performance.
    • The TTArtisan M-Z 6-Bit adapter doesn't provide autofocus, but has a reader for Leica's 6-bit lens codes. This makes 6-bit coded lenses behave like Ai-P lenses on the FTZ, except with no aperture control (as rangefinder lenses use pre-set apertures): EXIF data is automatically recorded, IBIS is set to the correct focal length and focus confirmation is supported.
  • For Leica R mount lenses
    • The FotodioX Leica R Lens to Nikon Z-Mount Camera Pro Lens Adapter allows Leica R bayonet mount lenses to operate on a Nikon Z. It is a fully manual design.
  • For M39/LTM lenses
    • The Novoflex Leica M39 Lens to Nikon Z-Mount Camera Adapter mechanical adapter that lets you mount Leica 39mm thread-mount (LTM / L39) rangefinder lenses onto Nikon Z-mount cameras.
    • The Urth M39 to Nikon Z Lens Mount Adapter is a manual mechanical adapter that lets you mount M39 screw-mount lenses onto Z-series cameras.
  • For M42 lenses
    • The Pholsy M42-N/Z allows you to mount M42 42mm screw-mount lenses onto Z-mount cameras.
  • For Micro Four Thirds lenses
    • The Pixco Manual Lens Adapter is a mechanical pass-through adapter which allows Micro Four Thirds lenses to be used on a Z-camera.
  • For Nikon F-mount lenses
    • The Viltrox NF-Z is largely identical to Nikon's original FTZ adapter, both in function and form. Like the FTZ, autofocus does not function with screw-drive AF/AF-D lenses. It has a USB-C port for firmware updates.
    • The MonsterAdapter LA-FZ1 is the first adapter that allows F-mount screw-driven AF and AF-D lenses to be used on Z cameras with full autofocus. It was showcased at CP+ 2025. Per their website, it "does NOT include autofocus support for AF-I, AF-S, and AF-P lenses, nor support of EMD electromagnetic aperture and lens VR."
  • For Nikon 1-mount lenses
    • There are no adapters, due in equal parts to the minimal flange difference (17mm on the 1-mount vs. 16mm on the Z-mount), vignetting from the small imaging circle (1-series was designed for the small CX format), and the short life that the lenses were manufactured (less than 7 years).
  • For Nikon IX-mount lenses
    • There are no commercially available adapters, as the IX lenses feature a protruding rear element and shroud, along with lacking a traditional mechanical aperture ring. However, as the IX-Nikkor lenses use the same electronic communications as Nikkor AF F-mount lenses with distance encoding (AF-D), they may be adapted, at a potential risk, to Z-mount cameras in DX (cropped sensor) mode.
  • For Nikon S-mount lenses - Outer bayonet
    • The Roxsen Nikon S mount rangefinder lens to Nikon Z mount mirrorless adapter can be used to mount outer bayonet rangefinder lenses. As these are manual lenses with a short flange distance, they use manual focus and manual exposure control.
  • For Nikon S-mount lenses - Inner bayonet
    • No adapters exist.
  • For Pentax K/DA lenses
    • The K&F Concept Pentax K/DA Lens to Nikon Z Manual Focus Adapter lets you mount Pentax K-mount and DA-series DSLR lenses onto Z-cameras.
    • The Fotodiox Pro Lens Mount Adapter (PKAF-NKZ-P) lets you mount Pentax K-mount (PK and PK/AF) lenses onto Nikon Z-mount mirrorless cameras.
    • The Urth ULMA-K-Z is a manual lens mount adapter allowing Pentax K-mount lenses to be attached to Z-mount cameras.
  • For Samsung NX lenses
    • There are no commercial, mass-produced lens adapters available .
  • For Sony E-mount lenses
    • The Fotodiox Pro Fusion SNE-NKZ adapts lenses with autofocus and image stabilization, as well as lens function button support.
    • The Megadap ETZ11 is similar to the Techart TZE-01/02 and adapts lenses with autofocus and image stabilization support. In contrast to the Techart adapter, the ETZ11 can be mounted on the Z50 and Zfc.
    • The Megadap ETZ21 and ETZ21 Pro are improved versions of the ETZ11, and provide full function E-mount support, including autofocus, image stabilization, full-time manual focus, and support for programmable lens buttons and aperture rings.
    • The Megadap ETZ21 Pro+ has weather sealing, improved mechanical structure. It is compatible with the Sony LA-EA5 A-to-E mount adapter, therefore it also supports Sony A-mount lenses through stacking the LA-EA5 on the ETZ21 Pro+. It is also compatible with RED Z-mount cameras.
    • The Meike Mount Adapter ETZ is compatible with a wide range of Sony, Tamron, Sigma and Meike lenses with Sony E-mount, and supports autofocus, aperture control, EXIF and image stabilization.
    • The Techart TZE-01/TZE-02 allows mounting Sony E-mount lenses on Z-mount cameras with full electronic integration. This adapter cannot be mounted on the Z50 or the Zfc.
    • The Viltrox E-Z AF Lens Mount Adapter adapts E-mount lenses with autofocus and full electronic integration. Also supports adapter firmware upgrades.
  • For Sony A-mount lenses
    • Stack the Sony LA-EA5 adapter on the Megadap ETZ21 Pro+ adapter, to adapt selected lenses (from A to E, then E to Z mount).

Z-mount accessories

Accessory port

The Z9 and Z8 use the same circular 10-pin accessory port (for a remote shutter release, external GPS receiver, etc.) as previous "pro-grade" Nikon DSLRs (such as the D3/D4/D5/D6 series).

The Z6/Z7 (and their successors) and the Z5 use the rectangular 8-pin accessory port introduced with the D90 and used on most other Nikon DSLRs since.

The Z30/Z50/Zfc/Zf (and their successors) and the Z5II/Z5IIC do not have an accessory port.

The ZR does not have the same type of accessory port, but rather, it has a 26-pin digital hot shoe for two-way communication. This allows the camera to supply power and send data to and receive data from attached compatible microphones and tally lamps.

Flashes

All Nikon Z cameras (other than the ZR, which has a digital accessory shoe) have a hot shoe, which allows the use of the same iTTL flash system (Nikon CLS) as Nikon DSLRs, which remains fully backward compatible and with third-party flashes and flash transmitters.

Third-party flashes can be used on Z-mount cameras, as long as they have the same basic hot shoe design; standards define the two pins required to trigger the flash. However, they won't be integrated into the Z-system camera menus, and need to have the power adjusted manually and have the user be mindful of the maximum sync speed limits of the camera.

Although not a separate accessory, the Z50II and Z50 have built-in flashes, in addition to the hot shoe.

Batteries

Nikon Z cameras can be powered by both a custom battery and, except for the original Z50, directly via a USB-C cable.

The battery in the camera powers every electronic component required to operate the camera, including the image sensor and processor, autofocus system, EVF and LCD, IBIS, Wi-Fi and Bluetooth, media reading and writing, and built-in flash. It additionally powers the electronic components of lenses, including autofocus motors, electronic aperture control, image stabilization, power zoom, and communication with the camera.

Each camera uses one of the three proprietary lithium-ion batteries. The battery is rechargeable in-camera via USB-C PD (USB Power Delivery) (except for the original Z50), along with being rechargeable outside the camera using an external Nikon charger.

Each of the battery types has multiple variants, as they improve on the designs over the years, increasing the capacity and adding the USB-C charging where the original variants did not support it. Most Z cameras use the same batteries of their "peer" DSLRs:

  • The Nikon Z9 uses EN-EL18/a/b/c/d batteries, introduced with the D4.
    In-camera charging using USB-C is available from the EN-EL18b onwards (introduced in 2017).
  • The Nikon Z5/Z6/Z7 (and their successors), Z8, Zf, and ZR use EN-EL15/a/b/c batteries, introduced with the D7000.
    The Z5II, Z5IIC, Z6III, Z8, Zf, and ZR do not officially support the original EN-EL15 battery, only the subsequent a/b/c versions (although the "Li-ion20" variant of the EN-EL15 does work in practice).
    In-camera charging using USB-C is supported for all of these cameras from the EN-EL15b onwards (introduced in 2018).
  • Only the Nikon Z50, Z50II, Z30, and Zfc use a new battery type, the EN-EL25/a, introduced with the Z50. Previous entry-level DSLRs like the D5600 or D3500 used the EN-EL14.
    In-camera charging via USB-C is supported for all of these cameras, except for the original Z50.
Battery compatibility matrix for Nikon Z cameras
Battery Camera Charging Rel
date
Ref
Type V mAh
USB-C
External
EN-EL18
d 10.8 3300 Yes No
No
Yes MH‑33 2021–12
c 2500 Yes MH‑26,
MH‑26a,
MH‑33
2018–07
b Yes 2017–03
a Yes
No MH‑26,
MH‑26a
2014–03
2000 No 2012–03
EN-EL15
c 7.0 2280 No
Yes No
Yes MH‑25a,
MH‑34
2020–07
b 1900 Yes MH‑25,
MH‑25a,
MH‑34
2018–11
a Yes
No MH‑25,
MH‑25a
2015
No No Yes
Yes
No No Yes
Yes
No No Yes
No 2010–09
EN-EL25
a 7.6 1250 No
No
Yes
Yes Yes

Yes
Yes MH‑32 2023–12
1120 Yes Yes Yes
Yes Yes 2019–10
Notes
  1. 1 2 Uses EN-EL15 battery.
  2. 1 2 Uses EN-EL25 battery.
  3. 1 2 3 4 5 6 7 The battery cannot be charged through USB-C.
  4. 1 2 Uses EN-EL18 battery.
  5. ↑ EN-EL25a only supported with Zfc FW 1.50 and above.
  6. ↑ EN-EL25a only supported with Z50 FW 2.50 and above.
  7. 1 2 The Z50 does not have USB-C charging.
  8. ↑ EN-EL25a only supported with Z30 FW 1.10 and above.

Battery and remote control grips

Battery grips are available for several models:

  • The MB-N10 is compatible with the Nikon Z5, Z6, Z6II, Z7, and Z7II, but is purely a battery grip with no vertical camera controls.
  • The MB-N11 is compatible with the Nikon Z6II, Z7II, and Z5II, and adds vertical camera controls.
  • The MB-N12 is compatible with the Nikon Z8 and also has vertical camera controls.
  • The MB-N14 is compatible with the Nikon Z6III, Z5II, Z6II, and Z7II, and it also has vertical camera controls. It was initially released with the Z6III.

Nikon does not offer vertical battery grips for the Z50II, Z50, Z30, Zfc, Zf, ZR, and Z5IIC. The Nikon Z9 has a built-in vertical battery grip that is integrated into its body, and thus doesn't need an add-on grip.

The MC-N10 is a remote-control grip for all Z cameras with USB-C (the first-generation Z50 is the sole camera to not use USB-C). It connects through a USB-C cable to the camera and replicates the right-hand controls of the camera body. It is designed for video applications and uses an ARRI rosette-type mount. Cameras introduced before its release require a firmware update to use it.

Grip compatibility matrix for Nikon Z cameras
Grip Camera
Connection
to camera
Battery for
powering
camera
Camera
controls
Wt. Rel
date
Ref
Name
Type
MB-N14
vertical
battery grip
Grip built-in
No No Yes No No Yes Yes No Yes No
No No
Internal; portion inserted into
camera battery slot
2× EN-EL15a/b/c
Yes
295 g 2024-06-12
MB-N12 Yes No No No No No No No No Yes
295 g 2023-05-10
MB-N11 No Yes No No Yes No Yes No
No Yes
290 g 2020-10-04
MB-N10 No Yes Yes No Yes Yes No No Yes No
300 g 2019-10-10
MC-N10
separate
remote grip
Yes
Yes Yes Yes
Yes
Yes Yes Yes
Yes
Yes Yes Yes
Yes
Yes No
Yes
USB-C Yes 205 g 2022-11-02
Notes
  1. 1 2 The Z5IIC lacks electrical connectors in the battery compartment, and thus does not support the MB-N11 and MB-N14
  2. 1 2 3 MB-N11/12/14 provide additional battery power, along with camera controls
  3. ↑ MB-N10 only provides additional battery power; it does not have camera controls
  4. ↑ MC-N10 only supported with Z9 FW 3.00 and above
  5. ↑ MC-N10 only supported with Z7II FW 1.50 and above
  6. ↑ MC-N10 only supported with Z7 FW 3.60 and above
  7. ↑ MC-N10 only supported with Z6II FW 1.50 and above
  8. ↑ MC-N10 only supported with Z6 FW 3.60 and above
  9. ↑ MC-N10 only supported with Z5 FW 1.40 and above
  10. ↑ MC-N10 only supported with Zfc FW 1.40 and above
  11. ↑ The Z50 does not have a USB-C port.
  12. ↑ MC-N10 only supported with Z30 FW 1.10 and above
  13. ↑ The MC-N10 can be powered by 2× 1.5V AA, or 2× 1.2V Ni-MH batteries, but these are only powering the grip. The USB-C connection only carries data communication, not power (in either direction).

Wireless control

The ML-L7 Bluetooth Remote Control can be used to wirelessly control many of the functions on select Z cameras. Cameras supported are the Z30, Z50, Z50II, Zf, Zfc, ZR, Z5, Z5II, Z5IIC, Z6II, Z6III, and Z7II. It provides functions to press the shutter, movie record, power zoom, multi-selector, OK, and Fn1/Fn2.

The Nikon SnapBridge app can be used via a paired smart device to remotely control several functions of the camera, including viewing a live view, shot framing, adjusting exposure settings (such as shutter speed, aperture, ISO, and white balance), doing tap-to-focus, and firing the shutter.

Microphones

The ME-1 Stereo Microphone is available to allow the creation of higher-quality audio than the cameras' built-in stereo microphones. It mounts on the hot shoe, and connects to the camera via the 3.5mm stereo mini-plug.

The ME-D10 Shotgun Microphone attaches to the 26-pin digital hot shoe of the Nikon ZR. It supports 32-bit float audio recording and is powered by and connected to the camera solely through the hot shoe.

Third-party microphones can be used on Z-mount cameras, as long as they can mount on the hot shoe and have a 3.5mm stereo mini-plug.

Underwater cases

As noted on their webpage, "Nikon does not produce underwater cases/housings for ... Z series cameras, however they are available from third-party companies."

Other accessories

Nikon makes two different caps for the lenses and cameras:

  • The LF-N1 is a rear lens cap. It protects the rear element of a Nikkor Z lens from dust, smudges, and scratches when the lens is detached from the camera body.
  • The BF-N1 is a body cap. It protects a Z-camera's sensor when a lens is not attached.

Table of Z-mount lenses

The following table contains the specifications for 183 Z-mount lenses, including all Nikon Z-mount lenses, as well as all autofocus third-party Z-mount lenses. Collecting all specifications for third-party lenses, including manual focus ones, isn't feasible due to the large number of brands producing a great variety of such lenses. Some special-use manual focus lenses (perspective control and fisheye) are in the tables in the following section.

Notes
  1. ↑ Aperture values are given as either:
    F-stop, starting with an f/
    T-stop, starting with a T

Other non-AF lenses

Collecting all specifications for third-party manual focus lenses isn't feasible due to the large number of brands producing a great variety of such lenses. However, some special-use manual focus lenses (perspective control and fisheye) are contained in the following sections.

Perspective control lenses

Perspective control lenses (PC), often called "tilt-shift lenses", offer adjustments that duplicate certain view camera movements.

The following table does not contain all PC lenses; it contains the specifications for six Z-mount manual focus tilt-shift and tilt-only lenses. None are S-line, nor do they have image stabilization, L-Fn buttons, or zoom. There are no autofocus tilt-shift lenses due to how they must be focused. Note that Nikon does not make a Z-mount lens of this type; classic F-mount Nikon PC-E lenses are usable via an FTZ II adapter,

Fisheye lenses

Fisheye lenses are ultra wide-angle lenses that produces strong visual distortion intended to create a wide panoramic or hemispherical image.: 145  Fisheye lenses achieve extremely wide angles of view, well beyond any rectilinear lens.

The following table does not contain all fisheye lenses; it contains the specifications for three Z-mount manual focus fisheye lenses. None are S-line, nor do they have image stabilization, L-Fn buttons, or zoom. There are some autofocus fisheyes in the Table of Z-mount lenses. Note that Nikon does not make a Z-mount lens of this type; classic F-mount Fisheye lenses are usable via an FTZ II adapter.

Firmware updates

Firmware updates are available from the Nikon website for all Nikon components of the Z-system: cameras, lenses, flashes, adapters, and teleconverters. They are released as needed to correct errors, enhance functionality, or add new capabilities. The component being updated must be currently attached to a Z-system camera (if not the camera itself), and can be updated using one of two methods:

  1. The update file can be downloaded from the Nikon site and copied to the root directory of a memory card, which is then inserted into the camera's card slot. The update is then initiated using the camera's menu option.
  2. The update can be downloaded via the paired Nikon SnapBridge app.

Firmware updates for third-party lenses and equipment and the techniques for updating vary; they are not integrated into the Nikon menuing system for updates. The manufacturer's website should be consulted for details. Many of the lenses (such as Viltrox and Tamron) have a USB-C port which is used during the update, along with possibly a dedicated utility from the manufacturer.

See also